Set of 7 Christmas bubble lights with 20 inch spacing between the bubble lights. The overall length of the bubble light set is 11.6 feet. The bubble lights have green and red bases with green flowers with a red center. The liquid in them is clear. The bubble lights have end to end connectors which allow you to add up to 6 bubble light sets together. These nostalgic Christmas bubble lights are for 120 volt lines.
Christmas bubble lights were a huge success when they first came out in the 1940’s. The success continued into the 1950’s and 60’s. Today while not as popular, they are still widely used and add a nostalgic feeling to Christmas trees.
Tip; What to do when the bubble lights bulb tubes ceases to bubble. Unplug the Christmas bubble lights from the wall outlet. Unscrew the bubble lights from the light socket and give the Christmas bubble light bulb a good shaking. When shaking the bubble lights the liquids will be mix together again, restoring the Christmas bubble lights bubbles to their original bubble light action.
Christmas holiday light bulbs safety instructions:
When using Christmas tree bubble lights, basic precautions should always be followed including
these christmas bubble light safety tips.
Always use the bubble lights in an upright position.
The bubble light bulbs must warm up for several minutes before the bubble light action will start.
The bubble lights contains ethylene chloride and the vapors are harmful. If a bubble light vial breaks, open the windows and ventilate the room. Do Not breath the fumees and keep the bubble lights out of the reach of children.
Do not use the bubble lights outdoors unless the christmas tree bubble lights are marked suitable for indoor and outdoor use. When outdoor christmas bubble lights are used in outdoor applications, connect the outdoor christmas lights to a ground fault circuit interrupting [GFCI] electrical outlets. If one is not provided, contact a qualified electrician for proper outdoor lights installation.
Seasonal party lights or Christmas bubble lights are not intended for permanent installation or use.
Do not mount or place christmas bubble lights near gas or electric heaters, fireplaces, candles or other similar sources of heat.
Do not secure the Christmas bubble light sets with staples or nails, or place on sharp hooks.
Do not let the christmas bubble light bulbs rest on the holiday lights supply cord or on any wire.
Unplug the christmas bubble light bulbs when leaving the house, when retiring for the night, or if the christmas tree lights are left unattended.
Your holiday bubble lights, christmas tree bubble lights or bubble lights are not toys! To avoid risk of fire burns, personal injury and electric shock the christmas bubble lights should not be played with or placed where small children can reach the bubble light bulbs.
To reduce the risk of fire or electrical shock do not mount or support the christmas tree lights or bubble lights in a manner that can cut or damage the bubble light sets.
Do not close your doors or windows on the christmas bubble lights or extension cords as this may damage the wire insulation.
Do not cover the christmas bubble light bulbs or bubble lights with cloth, paper or any material not part of the holiday light when in use.
Your christmas bubble lights are equipped with threaded screw in holiday light bulbs. Make sure that you do not over tighten the bubble light bulbs causing the protective glass covering to break or crack.
Always unplug your christmas bubble lights before installing or replacing the christmas bubble light bulbs.
Do not overload the electrical wiring of the bubble lights. Only connect the recommended amount of christmas bubble light sets [usually six sets if not stated in instructions] on one continues light string.
Christmas bubble lights with overload fuses.
A blown fuse indicates an overloaded circuit and you need to reduce the amount of bubble lights connected to the circuit. A blown fuse may also be caused by a short-circuit and the christmas bubble light set with the short-circuit should be discarded.
1.) Always unplug your christmas bubble lights before installing or replacing the christmas light fuses.
2.) Slide open the bubble light fuse access cover on top of the attachment plug towards the plug in metal blades.
3.) Remove the bubble light fuses carefully.
4.) To avoid the risk of fire replace the blown fuses with like amp and volt fuses that were provided with the christmas bubble lights.
5.) Slide closed the bubble light fuse access cover by sliding the cover closed so that all fuse tabs latch.
6.) To avoid the risk of fire do not replace the factory christmas bubble light plug. The factory bubble light plug contains a safety device (fu
